EZ-Go Speed ​​Chip Istruzioni

EZ-Go Speed ​​Chip Istruzioni

Un chip di velocità EZ-Go consente a determinati modelli di carrelli da golf di superare i limiti di velocità pre-programmati nel sistema elettronico del carrello. Il chip di velocità EZ-Go, a volte chiamato anche chip di libertà, è compatibile con golf cart che utilizzano un Power Drive System (PDS) elettrico e sono modelli dell'anno 2000 o successivi. Il chip aumenta la velocità massima del carrello da 13,5 mph a 19 mph. L'installazione del chip di libertà è semplice e non richiede strumenti.

Determina se il tuo carrello da golf può utilizzare il chip di velocità EZ-Go controllando il sistema di controllo. Aprire il sedile del passeggero e trovare il controller del computer vicino al pacco batteria. Se il controller del computer è dotato di un interruttore run-tow, è compatibile con il chip di velocità EZ-Go. Verificare inoltre che sul pannello sotto al volante sia presente un interruttore avanti / indietro. L'interruttore avanti / indietro dovrebbe essere nella posizione "neutrale", tra "avanti" e "indietro".

Commuta l'interruttore di scorrimento a "traino". Rimuovere la copertura ambientale dal controller del computer e inserire il chip di velocità EZ-Go nello slot nell'angolo in basso a destra. Il chip di velocità è sagomato appositamente per adattarsi a questa presa e ha un paio di fili rossi che sporgono dalla cima. Piegare i cavi rossi e sostituire la copertura ambientale.

Capovolgere l'interruttore "run-tow" nella posizione "run". Commuta l'interruttore avanti / indietro dalla posizione "neutrale" a "indietro" cinque volte in rapida successione. Dopo alcuni secondi, il controller del computer emetterà quattro segnali acustici, indicando che è stato spostato nella modalità di libertà.

Riportare l'interruttore di avviamento a "traino" e quindi "correre" per uscire dalla modalità di impostazione diagnostica. Ciò consente la modalità di libertà e consente al carrello di raggiungere una velocità massima di 19 mph. Chiudere il coperchio del sedile del passeggero sul controller del computer.

Premi il pulsante "avanti" e controlla la velocità con il pedale dell'acceleratore. Il carrello aumenterà gradualmente la velocità fino a raggiungere un massimo di 19 mph.
EZ-Go Speed ​​Chip Istruzioni

FAQ - 💬

❓ How do you bypass the speed sensor on a EZ Go golf cart?

👉 The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.

❓ How do you put a speed chip in a EZ Go golf cart?

👉 0:031:31How to Install | Golf Cart Personality PlugStart of suggested clipEnd of suggested clipLocate the position for the personality plug. If your vehicle is equipped with an old plug removingMoreLocate the position for the personality plug. If your vehicle is equipped with an old plug removing this card if not you can insert your new plug. Now.

❓ How can I make my electric EZ Go golf cart faster?

👉 6 Ways You Can Make a Golf Cart Faster

  1. Add More Torque to Your Golf Cart.
  2. Upgrade Your Golf Cart's Motor.
  3. Improve the High-Speed Controller of the Cart.
  4. Add Better Golf Cart Tires.
  5. Use a Higher Powered Golf Cart Battery.
  6. Watch the Weight in Your Golf Cart.

❓ What does an ezgo speed chip do?

👉 The EZ-Go speed chip, sometimes also called a freedom chip, is compatible with golf carts that use an electric Power Drive System (PDS) and are model year 2000 or newer. The chip increases the cart's maximum speed from 13.5 mph to 19 mph. Installation of the freedom chip is easy and requires no tools.

❓ How do I test my EZGO sensor?

👉 Take a digital multimeter and set it to the volts reading. Place the positive probe of the meter on the white wire terminal of the ITS. Release the accelerator pedal slowly. The reading should be in the 0.45V to 0.53V range when the micro-switch gets activated.

❓ Can you remove golf cart speed sensor?

👉 Where is the Speed Sensor Found on a golf cart? The speed sensor in a Club Car Precedent golf cart is located on the back of the motor. To remove the sensor, unplug the cables behind the motor. You can use a 5/16-inch socket to remove the pigtail connector and pop off the plastic housing that encases the speed sensor.

❓ How fast can a 48V golf cart go?

👉 12MPHStandard 36V and 48V golf carts are capable of the same top-end speed (12MPH). You can, however, make your golf cart go faster by doing a couple of things: Larger Tires - You can purchase larger tires. The larger the diameter of the wheels, the faster your golf cart will go.

❓ Where is the speed magnet on a golf cart?

👉 Where is the Speed Sensor Found on a golf cart? The speed sensor in a Club Car Precedent golf cart is located on the back of the motor. To remove the sensor, unplug the cables behind the motor. You can use a 5/16-inch socket to remove the pigtail connector and pop off the plastic housing that encases the speed sensor.

❓ How can I make my electric golf cart go faster without upgrading?

👉 There are a few things you can do to make your electric golf cart faster: Check the battery – Make sure the battery is in good condition and fully charged. A weak or damaged battery will slow down the cart. Check the tires – Inflated tires will help the cart move more easily over uneven terrain.

❓ How do I unlock Freedom mode on EZ Go?

👉 Toggle the forward/reverse switch from the "neutral" position to "reverse" five times in quick succession. After a few seconds, the computer controller will beep four times, indicating it has shifted into the freedom mode.

❓ How can I make my EZGO TXT 48V faster?

👉 How to Make EZGO Txt 48v Faster. You can make an EZGO TXT 48V go faster by changing the RPM or the speed settings of the cart. Replacing old batteries, unlocking the speed settings or changing the controller will make your EZGO golf cart much faster.

❓ What is an EZ-GO speed chip on a golf cart?

👉 An EZ-Go speed chip allows certain golf cart models to exceed pre-programmed speed limitations in the cart’s electronic system. The EZ-Go speed chip, sometimes also called a freedom chip, is compatible with golf carts that use an electric Power Drive System (PDS) and are model year 2000 or newer.

❓ How to fix an EZ GO speed controller that wont turn on?

👉 How to Repair an E-Z-GO Speed Controller 1 Flip the maintenance switch. All EZ-GO speed controllers are equipped with a maintenance switch that needs to be flipped before you begin work on repairing the problem. 2 Reset the battery cable. ... 3 Check your connections. ... 4 Test the solenoid. ... 5 Check your controller’s power output

❓ What does the EZGO controller do?

👉 Acceleration: The controller controls the speed of the vehicle. It also regulates the speed when you apply full throttle to the cart. Battery health maintenance: The controller makes sure that the battery is working well and is not overloaded. Parameter setup: The controller operates the EZGO cart as efficiently as it controls the speed parameters.

❓ How do you put a speed chip on a golf cart?

👉 The chip increases the cart’s maximum speed from 13.5 mph to 19 mph. Installation of the freedom chip is easy and requires no tools. Determine whether your golf cart can use the EZ-Go speed chip by checking the control system. Open the passenger seat and find the computer controller next to the battery pack.

Condividi:
Lasciare Un Commento